![]() ![]() All stencils are pre-cut and ready to use including an application squeegee, PPG paint charts for 1968 /1969 model years.ġ968-72 Brushed Aluminum plate with blue background. This kit includes color photo’s with specs in the photo’s, spec sheet and how to sheet along with paint information instructions. Ĭontains: Two Left & Right front header panel stencils along with upper rear hood panel stencils, two rear lower trunk lid stencils and a prespaced 40′ paint mask roll. ![]() Note: 40 foot prespaced paint mask roll to join the front header panel and rear hood stencils together. 1970-1972 Chevelle SS, El Camino SS, Sprint SP, & Monte Carlo hood spring (fits. Note: 40 foot prespaced paint mask roll to join the front header panel and rear hood stencils together, and for completion of the trunk stripe up to the rear window.Ĭolor photo how to sheet with specs in the photo’s.ġ968-69 El Camino Paint stencil kit Contains: Glasstek : H1115 : 1978 - 1982 : Chevrolet El Camino : Hood - Bolt on - Cowl Induction - 4 Inch 707.85: Glasstek : H1115 : 1978 - 1988 : Chevrolet Malibu : Hood - Bolt on - Cowl Induction - 4 Inch 707.85: Glasstek : H1120 : 1962 - 1965 : Chevrolet Chevy II : Hood - Bolt on - Cowl Induction - 4 Inch 707. This 1968-1969 Chevelle & El Camino hood spring fits either side. These hood latch assemblies are precisely manufactured to OE specifications and ready for a hassle-free installation. Left & Right front header panel and rear hood stencils. NOTE: This kit was created and released by us in 2007 to provide 1968 & 69 Chevelle owners a stripe kit similar to the 1970-2 Chevelle series.ġ968-69 Chevelle Paint stencil kit Contains: ![]() In this case, the interior release lever on your 1987 Chevrolet El Camino is probably stuck in the “open” position – push the release lever back and forth several times and then try to close your hood.1968-69 Chevelle/El Camino Dual Stripe Paint Stencil Kit Sometimes, especially on older El Caminos, you may have difficulty getting your hood to latch when you close it. If your original 1968-1969 El Camino hood is rusty or damaged, you can save yourself the hassle of bodywork with this brand new, exact reproduction hood. Opening the hood on your El Camino with a broken cable requires you to use a coat hanger to reach through the grille and release the latch on the bottom of the hood latch. If your hood still won't open, you may have a broken hood release cable. Best Quality Reproduction Hood Made From Original 19 Gauge Steel Correct Factory Style 2 Cowl Scoop EDP Coated Correct Inner Support Structure. Another option is to pull the interior hood release, then bang on the hood to see if that pops it open. If you need to open the hood with a stuck latch on your El Camino, simply pull up on the hood and it should pop up for you to release the second latch. Sometimes, the hood on Chevrolets gets stuck and won't pop up after the interior latch is released. Pop that flat steel hood and there’s a big orange bored-and-stroked 454 big-block, now displacing 511 cubic inches, with Billet Specialties. Light-duty haulers built in the mid-1960s were rarely preserved as collectibles. The video above shows you the location of both hood latches. For starters, pre-1968 El Camino projects can be a little difficult to find, due to the trucks working-class nature. Popping the hood, or bonnet, on your El Camino is a two step process, you need to release the hood latch inside your El Camino and then you need to release the safety latch under your hood in the front of your El Camino. This video shows you how to open the hood in your 1987 Chevrolet El Camino. ![]()
0 Comments
Leave a Reply. |